We provide thoroughly reviewed https://www.pass4itsure.com Cisco 640-816 using the training resources which are the best for Cisco 640-816 test, and to get certified by Microsoft Windows Store apps. It is a best choice to accelerate your career as a professional in the Information Technology industry. Now we add the latest Cisco 640-816 content and to print and share content.
Exam A QUESTION 1
To allow or prevent load balancing to network 172.16.3.0/24, which of the following commands could be used in R2? (Choose two.)
A. R2(config-if)#clock rate
B. R2(config-if)#bandwidth
C. R2(config-if)#ip ospf cost
D. R2(config-if)#ip ospf priority
E. R2(config-router)#distance ospf
Correct Answer: BC
QUESTION 2
After the network has converged, what type of messaging, if any, occurs between R3 and R4?
“Pass Any Exam. Any Time.” – www.actualtests.com 2
A. No messages are exchanged
B. Hellos are sent every 10 seconds.
C. The full database from each router is sent every 30 seconds.
D. The routing table from each router is sent every 60 seconds.
Correct Answer: B QUESTION 3
OSPF is configured using default classful addressing. With all routers and interfaces operational, how many networks will be in the routing table of R1 that are indicated to be learned by OSPF?
A. 2
B. 3
C. 4
D. 5
E. 6
F. 7
Correct Answer: C
QUESTION 4
“Pass Any Exam. Any Time.” – www.actualtests.com 3 R1 is configured with the default configuration of OSPF. From the following list of IP addresses configured on R1, which address will the OSPF process select as the router ID?
A. 192.168.0.1
B. 172.16.1.1
C. 172.16.2.1
D. 172.16.2.225
Correct Answer: A
QUESTION 5
DRAG DROP
Riverside Towing is redesigning the network that connects its three locations. The administrator gave the networking team 192 168.45 0 to use for addressing the entire network. After subnetting the address, the team is ready to assign the addresses. The administrator plans to configure ip subnet-zero and use RIP v2 as the routing protocol. As a member of the networking team, you must address the network and at the same time conserve unused addresses for future growth. With those goals in mind, drag the host addresses on the left to the correct router interface. One of the routers is partially configured. Move your mouse over a router to view its configuration. Not all of the host addresses on the left are necessary.
ActualTests.com
A.
B.
C.
D.
Correct Answer:
Cisco 640-816 tests containing questions that cover all sides of tested subjects that help our members to be prepared and keep high level of professionalism. The main purpose of Cisco 640-816 exam is to provide high quality test that can secure and verify knowledge, give overview of question types and complexity that can be represented on real exam certification
QUESTION 6
Which two statements describe characteristics of IPv6 unicast addressing? (Choose two.)
A. Global addresses start with 2000::/3.
B. Link-local addresses start with FE00::/12.
C. Link-local addresses start with FF00::/10.
D. There is only one loopback address and itis :: 1.
E. If a global address is assigned to an interface, then that is the only allowable address for the interface.
Correct Answer: AD
QUESTION 7
ActualTests.com
Refer to the exhibit. Given the partial configuration shown in the exhibit, why do internal workstations on the 192.168.1.0 network fail to access the Internet?
A. A NAT pool has not been defined.
B. The wrong interface is overloaded.
C. NAT has not been applied to the inside and outside interfaces.
D. The access list has not been applied to the proper interface to allow traffic out of the internal network. “Pass Any Exam. Any Time.” – www.actualtests.com 5
Correct Answer: C QUESTION 8
Refer to the exhibit. Hosts in network 192.168.2.0 are unable to reach hosts in network 192.168.3.0. Based on the output from RouterA, what are two possible reasons for the failure? (Choose two.)
A. Interface S0/0 on RouterB is administratively down.
B. Interface S0/0 on RouterA is configured with an incorrect subnet mask.
C. Interface S0/0 on RouterA is not receiving a clock signal from the CSU/DSU.
D. The IP address that is configured on S0/0 of RouterB is not in the correct subnet.
E. The encapsulation that is configured on S0/0 of RouterB does not match the encapsulation that is configured on S0/0 of RouterA.
F. The cable that is connected to S0/0 on RouterA is faulty.
Correct Answer: CE
QUESTION 9
A network administrator is explaining VTP configuration to a new technician. What should the network administrator tell the new technician about VTP configuration? (Choose three.)
“Pass Any Exam. Any Time.” – www.actualtests.com 6
A. A switch in the VTP client modecannot update its local VLAN database.
B. A trunk link must be configured between the switches to forward VTP updates.
C. A switch in the VTP server mode can update a switch in the VTP transparent mode.
D. A switch in the VTP transparent mode will forward updates that it receives to other switches.
E. A switch in the VTP server mode only updates switches in the VTP client mode that have a higher VTP revision number.
F. A switch in the VTP server mode will update switches in the VTP client mode regardless of the configured VTP domain membership.
Correct Answer: ABD
QUESTION 10
ActualTests.com
Refer to the exhibit. What statement is true of the configuration for this network?
A. The configuration that is shown provides inadequate outside address space for translation of the number of inside addresses that are supported.
B. Because of the addressing on interface FastEthernet0/1, the Serial0/0 interface address will not support the NAT configuration as shown
C. The number 1 referred to in the ip nat inside source command references access-list number 1.
D. ExternalRouter must be configured with static routes to networks 172.16.1.0/24 and 172.16.2.0/24.
Correct Answer: C QUESTION 11
Refer to the exhibit. Which mask is correct to use for the WAN link between the routers that will provide connectivity while wasting the least amount of addresses?
A. /23
B. /24
C. /25
D. /30
Correct Answer: D QUESTION 12
ActualTests.com
Refer to the exhibit. What can be determined about the interfaces of the Main_Campus router from the output shown?
A. The LAN interfaces are configured on different subnets.
B. Interface FastEthernet 0/0 is configured as a trunk.
C. The Layer 2 protocol of interface Serial 0/1 is NOT operational.
D. The router is a modular router with five FastEthernet interfaces.
E. Interface FastEthernet 0/0 is administratively deactivated.
“Pass Any Exam. Any Time.” – www.actualtests.com 8 Correct Answer: B QUESTION 13
What are two characteristics of Frame Relay point-to-point subinterfaces? (Choose two.)
A. They create split-horizon issues.
B. They require a unique subnet within a routing domain.
C. They emulate leased lines.
D. They are ideal for full-mesh topologies.
E. They require the use of NBMA options when using OSPF.
Correct Answer: BC QUESTION 14
ActualTests.com
Refer to the exhibit. Which switch provides the spanning-tree designated port role for the network segment that services the printers?
A. Switch1
B. Switch2
C. Switch3
D. Switch4
Correct Answer: C
We help you do exactly that with our high quality Cisco 640-816 Certification using the above training materials.Regardless of whichever computer you have, you just need to download one of the many Cisco 640-816 PDF readers that are available for free.