Good News! With Cisco https://www.pass4itsure.com/642-811.html exam dumps, you will never worry about your Cisco 642-811 exam, all the questions and answers are updated timely by our experts.Also now Flydumps.com is offering free Cisco 642-811 exam VCE player and PDF files for free on their website.
Exam A
QUESTION 1
What action should a network administrator take to enable VTP pruning on an entire management domain?
A. enable VTP pruning on any client switch in the domain
B. enable VTP pruning on every switch in the domain
C. enable VTP pruning on any switch in the management domain
D. enable VTP pruning on a VTP server in the management domain
Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 2
Refer to the exhibit.
On the basis of the information provided in the exhibit, which two sets of procedures are best practices for
Layer 2 and 3 failover alignment? (Choose two.)
A. Configure the D-SW1 switch as the active HSRP router and the STP root for all VLANs. Configure the D-SW2 switch as the standby HSRP router and backup STP root for all VLANs.
B. Configure the D-SW2 switch as the active HSRP router and the STP root for all VLANs. Configure the D-SW1 switch as the standby HSRP router and backup STP root for all VLANs.
C. Configure the D-SW1 switch as the active HSRP router and the STP root for VLANs 11 and 110. Configure the D-SW2 switch as the active HSRP router and the STP root for VLANs 12 and 120.
D. Configure the D-SW1 switch as the standby HSRP router and the backup STP root for VLANs 12 and
120.
Configure the D-SW2 switch as the standby HSRP router and the backup STP root for VLANs 11 and
110.
E. Configure the D-SW1 switch as the standby HSRP router and the STP root for VLANs 11 and 110. Configure the D-SW2 switch as the standby HSRP router and the STP root for VLANs 12 and 120.
F. Configure the D-SW1 switch as the active HSRP router and the backup STP root for VLANs 11 and
110.
Configure the D-SW2 switch as the active HSRP router and the backup STP root for VLANs 12 and
120.
Correct Answer: CD Section: (none) Explanation
Explanation/Reference:
QUESTION 3
Which two multicast IP addresses can be represented by the multicast MAC address 0100.5e0A.0A07? (Choose two.)
A. 228.10.10.7
B. 228.10.10.8
C. 228.10.138.7
D. 229.11.10.7
E. 229.138.10.7
F. 229.138.10.8
Correct Answer: AE Section: (none) Explanation
Explanation/Reference:
QUESTION 4
Which is a valid multicast MAC address?
A. 00-00-00-FA-11-67
B. 01-00-E0-56-AE-3C
C. 00-01-E0-A8-B2-C1
D. 01-00-5E-0A-08-CF
E. FF-FF-FF-FF-FF-FF
Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 5
A network is configured with VLANs 1 through 5. 802.1 Q trunking is enabled between all switches. Currently, access ports for VLAN 3 exist only on Switch3 and Switch6. What must the administrator do to ensure that the other switches do not receive unnecessary broadcast packets for VLAN 3 while still allowing all other VLAN packets to cross?
A. Configure VTP pruning.
B. Configure Switch3 and Switch6 as transparent switches.
C. Configure Switch1, Switch2, Switch4 and Switch5 as transparent switches.
D. Nothing is required. Only Switch3 and Switch6 will receive VLAN3 packets by default.
Correct Answer: A Section: (none) Explanation
Explanation/Reference: QUESTION 6
Which three statements are true regarding the above diagram? (Choose three.)
A. A trunk link will be formed.
B. Only VLANs 1-1001 will travel across the trunk link.
C. The native VLAN for Switch B is vlan 1.
D. DTP is not running on Switch A.
E. DTP packets are sent from Switch B.
Correct Answer: ACE Section: (none) Explanation
Explanation/Reference:
QUESTION 7
Examine the router output above. Which two items are correct? (Choose two.)
A. Router A will assume the active state if its priority is the highest.
B. If Ethernet 0/2 goes down, the standby router will take over.
C. When Ethernet 0/3 of RouterA comes back up, the priority will become 105.
D. The local IP address of Router A is 10.1.0.6.
E. The local IP address of Router A is 10.1.0.20.
Correct Answer: AC Section: (none) Explanation
Explanation/Reference:
QUESTION 8
Which two statements are true about a switched virtual interface (SVI)? (Choose two.)
A. An SVI is created by entering the no switchport command in interface configuration mode.
B. An SVI is created for the default VLAN (VLAN1) to permit remote switch administration by default.
C. An SVI provides a default gateway for a VLAN.
D. Multiple SVIs can be associated with a VLAN.
E. SVI is another name for a routed port.
Correct Answer: BC Section: (none) Explanation
Explanation/Reference:
QUESTION 9
Given the following configuration on a switch interface, what happens when a host with the MAC address of 0003.0003.0003 is directly connected to the switch port? switchport mode access switchport port-security switchport port-security maximum 2 switchport port-security mac-address 0002.0002.0002 switchport port-security violation shutdown
A. The port will shut down.
B. The host will be allowed to connect.
C. The host will be refused access.
D. The host can only connect through a hub/switch where 0002.0002.0002 is already connected.
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 10
Which spanning-tree feature will disable ports configured for PortFast in the event of a BPDU being received on those ports?
A. BPDUGuard
B. BPDU filtering
C. UDLD
D. Root Guard
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 11
Which three interface commands will configure the switch port to support a connected Cisco phone and to trust the CoS values received on the port if CDP discovers that a Cisco phone is attached? (Choose three.)
A. mls qos trust override cos
B. mls qos trust cos
C. mls qos trust device cisco-phone
D. switchport priority extend cos_value
E. switchport voice vlan vlan-id
Correct Answer: BCE Section: (none) Explanation
Explanation/Reference:
QUESTION 12
If there are two equal cost paths to the root switch, what is the next criterion to determine the root port?
A. lowest time to receive BPDUs
B. lowest port ID
C. lowest sender bridge ID
D. highest MAC address on the receiving port
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 13
LAB The information of the question VTP Domain name : cisco VLAN Ids 20 31 IP Addresses 172.16.71.1/24 172.16.132.1/24 These are your specific tasks:
1.
Configure the VTP information with the distribution layer switch as the VTP server
2.
Configure the VTP information with the access layer switch as a VTP client
3.
Configure VLANs on the distribution layer switch
4.
Configure inter-VLAN routing on the distribution layer switch
5.
Specific VLAN port assignments will be made as users are added to the access layer switches in the future.
6.
All VLANs and VTP configurations are to completed in the global configuration To configure the switch click on the host icon that is connected to the switch be way of a serial console cable.
Correct Answers: vtp server configuration: switch#conf t switch(config)#vtp mode server switch(config)#vtp domain CISCO switch(config)#vlan 20 switch(config)#vlan 31 switch(config)#int vlan 20 switch(if-config)#ip add 172.64.20.1 255.255.255.0 switch(if-config)#no shut switch(if-config)#int vlan 31 switch(if-config)#ip add 192.162.31.1 255.255.255.0 switch(if-config)#no shut switch(if-config)#exit switch#ip routing switch#copy run start vtp client configuration: switch#conf t switch(config)#vtp mode client switch(config)#vtp domain CISCO switch#copy run start
A.
B.
C.
D.
Correct Answer: Section: (none) Explanation
Explanation/Reference:
Answer: Check certifyme eEngine, Download from Member Center
QUESTION 14
In the use of 802.1X access control, which three protocols are allowed through the switch port before authentication takes place? (Choose three.)
A. STP
B. CDP
C. EAP MD5
D. TACACS+
E. EAP-over-LAN
F. protocols not filtered by an ACL
Correct Answer: ABE Section: (none) Explanation
Explanation/Reference:
QUESTION 15
Which technology manages multicast traffic at Layer 2 by configuring Layer 2 LAN interfaces dynamically to forward multicast traffic only to those interfaces that want to receive it?
A. IGMP
B. IGMP snooping
C. PIM-DM
D. DVMRP
E. MOSPF
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 16
Refer to the above graphic. Switch A, the root bridge, is connected directly to Switch B over link L1 and to Switch C over link L2. The Layer 2 LAN interface on Switch C that is connected directly to Switch B is in the blocking state. If Switch C detects a link failure on the currently active link L2 on the root port, which spanning tree enhancement will allow Switch C to unblock the blocked port and transition it to forwarding without going through the listening and learning states?
A. PortFast
B. UplinkFast
C. BackboneFast
D. rapid spanning tree
Correct Answer: B Section: (none) Explanation
Explanation/Reference: QUESTION 17
What are three disadvantages of a router-on-a-stick configuration for InterVLAN routing? (Choose three.)
A. InterVLAN routing cannot be filtered by the router.
B. The router becomes a single point of failure for the network.
C. Routers will not route STP BPDUs.
D. There is a possibility of inadequate bandwidth for each VLAN.
E. Additional overhead on the router can occur.
F. NetFlow Switching is required for InterVLAN accounting.
Correct Answer: BDE Section: (none) Explanation
Explanation/Reference:
QUESTION 18
Refer to the exhibit. Which set of commands contains the minimum number of commands necessary on the Cat_3550 switch for the host in VLAN 2 to be able to ping the host in VLAN 3? e
A. ip routing
B. ip routingrouter eigrp 1network 10.0.0.0
C. router eigrp 1network 10.0.0.0
D. ip routingrouter eigrp 1redistribute connectednetwork 10.0.0.0network 200.1.1.0no auto-summary
E. ip routingrouter eigrp 1redistribute connectednetwork 10.0.0.0no auto-summary
Correct Answer: E Section: (none) Explanation
Explanation/Reference:
QUESTION 19
Which statement is correct about 802.1Q trunking?
A. Both switches must be in the same VTP domain.
B. The encapsulation type on both ends of the trunk does not have to match.
C. The native VLAN on both ends of the trunk must be VLAN 1.
D. 802.1Q trunking can only be configured on a Layer 2 port.
E. In 802.1Q trunking, all VLAN packets are tagged on the trunk link, except the native VLAN.
Correct Answer: E Section: (none) Explanation
Explanation/Reference:
QUESTION 20
Which two statements about the various implementations of STP are true? (Choose two.)
A. Common Spanning Tree maintains a separate spanning-tree instance for each VLAN configured in the network.
B. The Spanning Tree Protocol (STP) is an evolution of the IEEE 802.1w standard.
C. Per-VLAN Spanning Tree (PVST) supports 802.1Q trunking.
D. Per-VLAN Spanning Tree Plus(PVST+) is an enhancement to 802.1Q specification and is supported only on Cisco devices.
E. Rapid Spanning Tree Protocol (RSTP) includes features equivalent to Cisco PortFast, UplinkFast, and BackboneFast for faster network reconvergence.
F. Multiple Spanning Tree (MST) assumes one spanning-tree instance for the entire Layer 2 network, regardless of the multiple number of VLANs.
Correct Answer: DE Section: (none) Explanation
Explanation/Reference:
The Cisco 642-811 certification can make you a competent person.It may enable a technician to know about the Cisco https://www.pass4itsure.com/642-811.html configurations,get information about the Cisco 642-811 data center products and hardware and knowledge about Cisco 642-811 united computing systems.