We provide thoroughly reviewed Cisco 640-822 using the training resources which are the best for Cisco https://www.pass4itsure.com/640-822.html test, and to get certified by Microsoft Windows Store apps. It is a best choice to accelerate your career as a professional in the Information Technology industry. Now we add the latest Cisco 640-822 content and to print and share content.
The Cisco 640-822 Interconnecting Cisco Networking Devices Part 2 (ICND2) is the exam associated with the Cisco Certified Network Associate certification. Candidates can prepare for this exam by taking the Interconnecting Cisco Networking Devices Part 2 (ICND2) v1.0 course. This exam tests a candidate’s knowledge and skills required to successfully install, operate, and troubleshoot a small to medium size enterprise branch network. The exam covers topics on VLSM and IPv6 addressing; extending switched networks with VLANs; configuring, verifying and troubleshooting VLANs; the VTP, RSTP, OSPF and EIGRP protocols; determining IP routes; managing IP traffic with access lists; NAT and DHCP; establishing point-to- point connections; and establishing Frame Relay connections.
The following topics are general guidelines for the content likely to be included on the Interconnecting Cisco Networking Devices Part 2 exam. However, other related topics may also appear on any specific delivery of the exam. In order to better reflect the contents of the exam and for clarity purposes, the guidelines below may change at any time without notice.
Topic 1 – Configure, verify and troubleshoot a switch with VLANs and interswitch communications. (63 Questions) Describe enhanced switching technologies (including: VTP, RSTP, VLAN, PVSTP, 802.1q) Describe how VLANs create logically separate networks and the need for routing between them Configure, verify, and troubleshoot VLANs Configure, verify, and troubleshoot trunking on Cisco switches Configure, verify, and troubleshoot interVLAN routing Configure, verify, and troubleshoot VTP Configure, verify, and troubleshoot RSTP operation Interpret the output of various show and debug commands to verify the operational status of a Cisco switched network Implement basic switch security (including: port security, unassigned ports, trunk access, etc.)
Topic 2 – Implement IP addressing and Services(18 Questions) Calculate and apply a VLSM IP addressing design to a network Determine the appropriate classless addressing scheme using VLSM and summarization to satisfy addressing requirements in a LAN/WAN environment Describe the technological requirements for running IPv6 (including: protocols, dual stack, tunneling, etc) Describe IPv6 addresses Identify and correct common problems associated with IP addressing and host configurations
Topic 3 – Configure and troubleshoot basic operation and routing on Cisco devices. (69 Questions) Compare and contrast methods of routing and routing protocols Configure, verify and troubleshoot OSPF Configure, verify and troubleshoot EIGRP Verify configuration and connectivity using ping, traceroute, and telnet or SSH Troubleshoot routing implementation issues Verify router hardware and software operation using SHOW DEBUG commands Implement basic router security
Topic 4 – Implement, verify, and troubleshoot NAT and ACLs in a medium-size Enterprise branch office network. (20 Questions) Describe the purpose and types of access control lists Configure and apply access control lists based on network filtering requirements Configure and apply an access control list to limit telnet and SSH access to the router Verify and monitor ACL’s in a network environment Troubleshoot ACL implementation issues Explain the basic operation of NAT Configure Network Address Translation for given network requirements using CLI Troubleshoot NAT implementation issues
Topic 5 – Implement and verify WAN links. (24 Questions) Configure and verify Frame Relay on Cisco routers Troubleshoot WAN implementation issues Describe VPN technology (including: importance, benefits, role, impact, components) Configure and vary PPP connection between Cisco routers
QUESTION 1 Which three statements are true about the operation of a full-duplex Ethernet network? (Choose three.)
A. There are no collisions in full-duplex mode.
B. A dedicated switch port is required for each full-duplex node.
C. Ethernet hub ports are preconfigured for full-duplex mode.
D. In a full-duplex environment, the host network card must check for the availability of the network media before transmitting.
E. The host network card and the switch port must be capable of operating in full-duplex mode.
Correct Answer: ABE
Which router command can be used to determine the status of Serial 0/0?
A. show ip route
B. show interfaces
C. show s0/0 status
D. debug s0/0
E. show run
F. show version
Correct Answer: B
QUESTION 3 Which commands display information about the Cisco IOS software version currently running on a router? (Choose three.)
A. show running-config
B. show stacks
C. show version
D. show flash
E. show protocols
F. show IOS
Correct Answer: ACD
QUESTION 4 After the shutdown command has been issued on the serial 0/0 interface, what will be displayed when the show interface serial 0/0 command is issued by the administrator?
A. Serial0/0 is administratively down, line protocol is down
B. Serial0/0 is down, line protocol is down
C. Serial0/0 is up, line protocol is down
D. Serial0/0 is administratively down, line protocol is administratively down
E. Serial0/0 is up, line protocol is up
F. Serial0/0 is down, line protocol is up
Correct Answer: A
Refer to the output of the three router commands shown in the exhibit. A new technician has been told to add a new LAN to the company router. Why has the technician received the error message that is shown following the last command?
A. The interface was already configured.
B. The interface type does not exist on this router platform.
C. The IOS software loaded on the router is outdated.
D. The router does not support LAN interfaces that use Ethernet.
E. The command was entered from the wrong prompt.
Correct Answer: B
QUESTION 6 The system LED is amber on a Cisco Catalyst 2950 series switch. What does this indicate?
A. The system is malfunctioning.
B. The system is not powered up.
C. The system is powered up and operational.
D. The system is forwarding traffic.
E. The system is sensing excessive collisions.
“First Test, First Pass” – www.lead2pass.com 5
Cisco 640-822 Exam
Correct Answer: A
Refer to the exhibit. SwitchA receives the frame with the addressing shown.
According to the command output also shown in the exhibit, how will SwitchA
handle this frame?
A. It will drop the frame.
B. It will forward the frame out port Fa0/3 only.
C. It will flood the frame out all ports.
D. It will flood the frame out all ports except Fa0/3.
Correct Answer: D
QUESTION 8 Refer to the topology and partial configurations shown in the exhibit. The network administrator has finished configuring the NewYork and Sydney routers and issues the command ping Sydney from the NewYork router. The ping fails. What command or set of commands should the network administrator issue to correct this problem?
A. Sydney(config)# interface s0/0 Sydney(config-if)# cdp enable
B. Sydney(config)# interface s0/0 Sydney(config-if)# no shut
C. Sydney(config)# line vty 0 4 Sydney(config)# login Sydney(config)# password Sydney
D. Sydney(config)# ip host Sydney 10.1.1.9
E. Sydney(config)# interface s0/0 Sydney(config-if)# ip address 10.1.1.5 255.255.255.252 NewYork(config)# ip host Sydney 10.1.1.5
Correct Answer: E
Which two statements describe the operation of the CSMA/CD access method?
A. In a CSMA/CD collision domain, multiple stations can successfully transmit data simultaneously.
B. In a CSMA/CD collision domain, stations must wait until the media is not in use before transmitting.
C. The use of hubs to enlarge the size of collision domains is one way to improve the operation of the CSMA/CD access method.
D. After a collision, the station that detected the collision has first priority to resend the lost data.
E. After a collision, all stations run a random backoff algorithm. When the backoff delay period has expired, all stations have equal priority to transmit data.
F. After a collision, all stations involved run an identical backoff algorithm and then synchronize with each other prior to transmitting data.
Correct Answer: BE
QUESTION 10 Refer to the topology and MAC address table shown in the exhibit. Host A sends a data frame to host D. What will the switch do when it receives the frame from host A?
A. The switch will add the source address and port to the MAC address table and forward the frame to host D.
B. The switch will discard the frame and send an error message back to host A.
C. The switch will flood the frame out of all ports except for port Fa0/3.
D. The switch will add the destination address of the frame to the MAC address table and forward the frame to host D.
Correct Answer: A
We help you do exactly that with our high quality Cisco 640-822 Certification using the above training materials.Regardless of whichever computer you have, you just need to download one of the many Cisco https://www.pass4itsure.com/640-822.html PDF readers that are available for free.